ADSBexchange.com
Custom Image - System Info

(..back to main menu)

Feeder Name
Public IP
 
StoppStoyen.no_4

31.45.94.24

Local IP: 
127.0.0.1

Configured Location: 
59.8, 10.8

Zerotier Status: 
zerotier is disabled.

Uptime: 
Current Time: Thu May 21 01:45:46 AEST 2026
Uptime: up 2 days, 9 minutes
Since 2026-05-19 01:36:09

Voltage Drops: 
Status: 0x0
Undervolted:
   Now: NO
   Run: NO
Throttled:
   Now: NO
   Run: NO
Frequency Capped:
   Now: NO
   Run: NO
Softlimit:
   Now: NO
   Run: NO

CPU temp=63.7'C
Redline=80'C

Messages since boot: 
1090mhz: 842,417
978mhz: 0
Tracks: 735

Installed SDR serials
(vendor code 0bda:*) 
77771111153705700

Position Count By Type: (info)
Last 1 Minute
Last 5 Minutes
Last 15 Minutes
Since Boot
 
{
  "adsb_icao": 67,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

{
  "adsb_icao": 502,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

{
  "adsb_icao": 1386,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

{
  "adsb_icao": 94890,
  "adsb_icao_nt": 0,
  "adsr_icao": 0,
  "tisb_icao": 0,
  "adsc": 0,
  "mlat": 0,
  "other": 0,
  "mode_s": 0,
  "adsb_other": 0,
  "adsr_other": 0,
  "tisb_trackfile": 0,
  "tisb_other": 0,
  "mode_ac": 0,
  "unknown": 0
}

Current WiFi Status: 
wlan0     IEEE 802.11  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=31 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on

Current IP Status: 
eth0: flags=4163  mtu 1500
        inet 10.0.0.101  netmask 255.255.255.0  broadcast 10.0.0.255
        ether d8:3a:dd:35:2f:28  txqueuelen 1000  (Ethernet)
        RX packets 2122451  bytes 284258212 (271.0 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1033866  bytes 140351770 (133.8 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 1534969  bytes 117896124 (112.4 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1534969  bytes 117896124 (112.4 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

tailscale0: flags=4305  mtu 1280
        inet 100.68.61.102  netmask 255.255.255.255  destination 100.68.61.102
        unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  txqueuelen 500  (UNSPEC)
        RX packets 591  bytes 59924 (58.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 590  bytes 36553 (35.6 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4099  mtu 1500
        inet 172.23.45.1  netmask 255.255.255.0  broadcast 0.0.0.0
        ether d8:3a:dd:35:2f:29  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 48  bytes 9418 (9.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

IP Route: 
default via 10.0.0.1 dev eth0 proto dhcp src 10.0.0.101 metric 202 
10.0.0.0/24 dev eth0 proto dhcp scope link src 10.0.0.101 metric 202 
172.23.45.0/24 dev wlan0 proto kernel scope link src 172.23.45.1 linkdown

readsb.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
May 20 23:04:44 adsbexchange readsb[25637]: cb transfer status: 1, canceling...
May 20 23:04:44 adsbexchange readsb[25637]: rtlsdr_read_async returned unexpectedly, probably lost the USB device, bailing out
May 20 23:04:44 adsbexchange readsb[25637]: Wed May 20 23:04:44 2026 AEST  Abnormal exit.
May 20 23:04:44 adsbexchange systemd[1]: readsb.service: Main process exited, code=exited, status=1/FAILURE
May 20 23:04:44 adsbexchange systemd[1]: readsb.service: Failed with result 'exit-code'.
May 20 23:04:44 adsbexchange systemd[1]: readsb.service: Consumed 52.135s CPU time.
May 20 23:04:59 adsbexchange systemd[1]: readsb.service: Scheduled restart job, restart counter is at 25.
May 20 23:04:59 adsbexchange systemd[1]: Stopped readsb ADS-B receiver.
May 20 23:04:59 adsbexchange systemd[1]: readsb.service: Consumed 52.135s CPU time.
May 20 23:04:59 adsbexchange systemd[1]: Started readsb ADS-B receiver.
May 20 23:04:59 adsbexchange readsb[30510]: Wed May 20 23:04:59 2026 AEST  readsb starting up.
May 20 23:04:59 adsbexchange readsb[30510]: readsb version: wiedehopf git: d809bd8 (committed: Wed Sep 7 13:47:41 2022 0200)
May 20 23:04:59 adsbexchange readsb[30510]: Using lat:   59.8110, lon:   10.8195
May 20 23:04:59 adsbexchange readsb[30510]: 30002: Raw TCP output port
May 20 23:04:59 adsbexchange readsb[30510]: 30005: Beast TCP output port
May 20 23:04:59 adsbexchange readsb[30510]: 30154: Position json output port
May 20 23:04:59 adsbexchange readsb[30510]: 30003: SBS TCP output ALL port
May 20 23:04:59 adsbexchange readsb[30510]: 30152: API output port
May 20 23:04:59 adsbexchange readsb[30510]: 30001: Raw TCP input port
May 20 23:04:59 adsbexchange readsb[30510]: 30004: Beast TCP input port
May 20 23:04:59 adsbexchange readsb[30510]: 30104: Beast TCP input port
May 20 23:04:59 adsbexchange readsb[30510]: rtlsdr: using device #0: Generic RTL2832U (Generic, RTL2832U, SN 77771111153705700)
May 20 23:04:59 adsbexchange readsb[30510]: Found Rafael Micro R820T tuner
May 20 23:05:00 adsbexchange readsb[30510]: rtlsdr: enabling tuner AGC
May 20 23:05:00 adsbexchange readsb[30510]: Allocating 16 zero-copy buffers
May 21 01:24:20 adsbexchange readsb[30510]: cb transfer status: 1, canceling...
May 21 01:24:20 adsbexchange readsb[30510]: rtlsdr_read_async returned unexpectedly, probably lost the USB device, bailing out
May 21 01:24:20 adsbexchange readsb[30510]: Thu May 21 01:24:20 2026 AEST  Abnormal exit.
May 21 01:24:20 adsbexchange systemd[1]: readsb.service: Main process exited, code=exited, status=1/FAILURE
May 21 01:24:20 adsbexchange systemd[1]: readsb.service: Failed with result 'exit-code'.
May 21 01:24:20 adsbexchange systemd[1]: readsb.service: Consumed 11min 10.351s CPU time.
May 21 01:24:35 adsbexchange systemd[1]: readsb.service: Scheduled restart job, restart counter is at 26.
May 21 01:24:35 adsbexchange systemd[1]: Stopped readsb ADS-B receiver.
May 21 01:24:35 adsbexchange systemd[1]: readsb.service: Consumed 11min 10.351s CPU time.
May 21 01:24:35 adsbexchange systemd[1]: Started readsb ADS-B receiver.
May 21 01:24:35 adsbexchange readsb[27778]: Thu May 21 01:24:35 2026 AEST  readsb starting up.
May 21 01:24:35 adsbexchange readsb[27778]: readsb version: wiedehopf git: d809bd8 (committed: Wed Sep 7 13:47:41 2022 0200)
May 21 01:24:35 adsbexchange readsb[27778]: Using lat:   59.8110, lon:   10.8195
May 21 01:24:35 adsbexchange readsb[27778]: 30002: Raw TCP output port
May 21 01:24:35 adsbexchange readsb[27778]: 30005: Beast TCP output port
May 21 01:24:35 adsbexchange readsb[27778]: 30154: Position json output port
May 21 01:24:35 adsbexchange readsb[27778]: 30003: SBS TCP output ALL port
May 21 01:24:35 adsbexchange readsb[27778]: 30152: API output port
May 21 01:24:35 adsbexchange readsb[27778]: 30001: Raw TCP input port
May 21 01:24:35 adsbexchange readsb[27778]: 30004: Beast TCP input port
May 21 01:24:35 adsbexchange readsb[27778]: 30104: Beast TCP input port
May 21 01:24:35 adsbexchange readsb[27778]: rtlsdr: using device #0: Generic RTL2832U (Generic, RTL2832U, SN 77771111153705700)
May 21 01:24:35 adsbexchange readsb[27778]: Found Rafael Micro R820T tuner
May 21 01:24:35 adsbexchange readsb[27778]: rtlsdr: enabling tuner AGC
May 21 01:24:35 adsbexchange readsb[27778]: Allocating 16 zero-copy buffers
May 21 01:36:20 adsbexchange readsb[27778]: cb transfer status: 1, canceling...
May 21 01:36:20 adsbexchange readsb[27778]: rtlsdr_read_async returned unexpectedly, probably lost the USB device, bailing out
May 21 01:36:20 adsbexchange readsb[27778]: Thu May 21 01:36:20 2026 AEST  Abnormal exit.
May 21 01:36:20 adsbexchange systemd[1]: readsb.service: Main process exited, code=exited, status=1/FAILURE
May 21 01:36:20 adsbexchange systemd[1]: readsb.service: Failed with result 'exit-code'.
May 21 01:36:20 adsbexchange systemd[1]: readsb.service: Consumed 57.124s CPU time.
May 21 01:36:35 adsbexchange systemd[1]: readsb.service: Scheduled restart job, restart counter is at 27.
May 21 01:36:35 adsbexchange systemd[1]: Stopped readsb ADS-B receiver.
May 21 01:36:35 adsbexchange systemd[1]: readsb.service: Consumed 57.124s CPU time.
May 21 01:36:35 adsbexchange systemd[1]: Started readsb ADS-B receiver.
May 21 01:36:35 adsbexchange readsb[675]: Thu May 21 01:36:35 2026 AEST  readsb starting up.
May 21 01:36:35 adsbexchange readsb[675]: readsb version: wiedehopf git: d809bd8 (committed: Wed Sep 7 13:47:41 2022 0200)
May 21 01:36:35 adsbexchange readsb[675]: Using lat:   59.8110, lon:   10.8195
May 21 01:36:35 adsbexchange readsb[675]: 30002: Raw TCP output port
May 21 01:36:35 adsbexchange readsb[675]: 30005: Beast TCP output port
May 21 01:36:35 adsbexchange readsb[675]: 30154: Position json output port
May 21 01:36:35 adsbexchange readsb[675]: 30003: SBS TCP output ALL port
May 21 01:36:35 adsbexchange readsb[675]: 30152: API output port
May 21 01:36:35 adsbexchange readsb[675]: 30001: Raw TCP input port
May 21 01:36:35 adsbexchange readsb[675]: 30004: Beast TCP input port
May 21 01:36:35 adsbexchange readsb[675]: 30104: Beast TCP input port
May 21 01:36:35 adsbexchange readsb[675]: rtlsdr: using device #0: Generic RTL2832U (Generic, RTL2832U, SN 77771111153705700)
May 21 01:36:36 adsbexchange readsb[675]: Found Rafael Micro R820T tuner
May 21 01:36:36 adsbexchange readsb[675]: rtlsdr: enabling tuner AGC
May 21 01:36:36 adsbexchange readsb[675]: Allocating 16 zero-copy buffers
May 21 01:45:22 adsbexchange readsb[675]: cb transfer status: 1, canceling...
May 21 01:45:22 adsbexchange readsb[675]: rtlsdr_read_async returned unexpectedly, probably lost the USB device, bailing out
May 21 01:45:22 adsbexchange readsb[675]: Thu May 21 01:45:22 2026 AEST  Abnormal exit.
May 21 01:45:22 adsbexchange systemd[1]: readsb.service: Main process exited, code=exited, status=1/FAILURE
May 21 01:45:22 adsbexchange systemd[1]: readsb.service: Failed with result 'exit-code'.
May 21 01:45:22 adsbexchange systemd[1]: readsb.service: Consumed 43.143s CPU time.
May 21 01:45:37 adsbexchange systemd[1]: readsb.service: Scheduled restart job, restart counter is at 28.
May 21 01:45:37 adsbexchange systemd[1]: Stopped readsb ADS-B receiver.
May 21 01:45:37 adsbexchange systemd[1]: readsb.service: Consumed 43.143s CPU time.
May 21 01:45:37 adsbexchange systemd[1]: Started readsb ADS-B receiver.
May 21 01:45:37 adsbexchange readsb[4833]: Thu May 21 01:45:37 2026 AEST  readsb starting up.
May 21 01:45:37 adsbexchange readsb[4833]: readsb version: wiedehopf git: d809bd8 (committed: Wed Sep 7 13:47:41 2022 0200)
May 21 01:45:37 adsbexchange readsb[4833]: Using lat:   59.8110, lon:   10.8195
May 21 01:45:37 adsbexchange readsb[4833]: 30002: Raw TCP output port
May 21 01:45:37 adsbexchange readsb[4833]: 30005: Beast TCP output port
May 21 01:45:37 adsbexchange readsb[4833]: 30154: Position json output port
May 21 01:45:37 adsbexchange readsb[4833]: 30003: SBS TCP output ALL port
May 21 01:45:37 adsbexchange readsb[4833]: 30152: API output port
May 21 01:45:37 adsbexchange readsb[4833]: 30001: Raw TCP input port
May 21 01:45:37 adsbexchange readsb[4833]: 30004: Beast TCP input port
May 21 01:45:37 adsbexchange readsb[4833]: 30104: Beast TCP input port
May 21 01:45:37 adsbexchange readsb[4833]: rtlsdr: using device #0: Generic RTL2832U (Generic, RTL2832U, SN 77771111153705700)
May 21 01:45:37 adsbexchange readsb[4833]: Found Rafael Micro R820T tuner
May 21 01:45:37 adsbexchange readsb[4833]: rtlsdr: enabling tuner AGC
May 21 01:45:37 adsbexchange readsb[4833]: Allocating 16 zero-copy buffers

dump978-fa.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
-- No entries --

autogain1090.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
May 19 02:46:49 adsbexchange systemd[1]: Started autogain for readsb or dump1090-fa.
May 19 02:46:49 adsbexchange autogain1090[14012]: Gain already at maximum! (0.270% messages >-3dB)
May 19 02:46:49 adsbexchange systemd[1]: autogain1090.service: Succeeded.
May 20 02:43:18 adsbexchange systemd[1]: Started autogain for readsb or dump1090-fa.
May 20 02:43:18 adsbexchange autogain1090[5044]: No gain change needed, percentage of messages >-3dB is in nominal range. (1.538%)
May 20 02:43:18 adsbexchange systemd[1]: autogain1090.service: Succeeded.

tar1090.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
May 18 06:25:05 adsbexchange systemd[1]: Started tar1090 - compress dump1090 json data.
May 19 02:21:19 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 02:21:21 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 02:55:09 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 02:55:13 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 03:17:24 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 03:17:30 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 08:02:16 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 08:02:20 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 10:43:25 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 10:43:32 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 11:09:27 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 11:09:33 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 12:34:10 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 12:34:14 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 16:56:03 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 16:56:05 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 17:58:25 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 17:58:29 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 18:02:26 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 18:02:32 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 18:14:10 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 18:14:12 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 19 19:15:12 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 19 19:15:17 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 20 03:32:41 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 20 03:32:43 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 20 03:40:54 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 20 03:40:58 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 20 22:53:56 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 20 22:53:58 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 20 23:04:56 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 20 23:05:01 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!
May 21 01:45:34 adsbexchange tar1090[640]: No aircraft.json found in /run/readsb during the last 30 seconds! Try restarting dump1090 or reinstalling tar1090 if you switched dump1090 to readsb!
May 21 01:45:39 adsbexchange tar1090[640]: Found aircraft.json in /run/readsb, continuing operation as per usual!

tar1090-978.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
-- No entries --

adsbexchange-feed.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
May 20 01:21:35 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 01:36:44 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 01:51:47 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 02:07:15 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 02:22:23 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 02:37:24 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 02:52:51 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 03:08:12 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 03:23:19 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 03:32:28 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 20 03:32:28 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:32:28 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:32:29 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:32:31 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:32:35 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:32:44 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 20 03:38:20 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 03:40:41 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 20 03:40:41 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:40:42 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:40:43 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:40:45 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:40:49 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 03:40:57 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 20 03:54:21 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 04:09:31 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 04:24:38 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 04:46:09 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 05:01:15 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 05:16:25 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 05:34:51 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 05:56:22 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 06:11:41 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 06:27:17 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 06:47:07 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 07:02:08 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 07:18:55 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 07:35:37 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 08:01:08 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 09:07:50 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 20 09:07:50 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 09:07:51 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 09:07:52 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 09:07:54 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 09:07:58 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 09:08:06 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 20 20:31:44 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 20:54:41 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 21:09:49 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 21:26:36 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 21:42:09 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 21:57:26 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 22:12:51 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 22:28:12 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 22:51:15 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 22:53:42 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 20 22:53:42 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 22:53:43 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 22:53:44 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 22:53:46 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 22:53:50 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 22:53:58 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 20 23:04:44 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 20 23:04:44 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 23:04:44 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 23:04:45 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 23:04:48 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 23:04:52 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 20 23:05:00 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 20 23:07:36 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 23:22:38 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 20 23:48:10 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 00:04:06 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 00:19:25 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 00:34:26 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 00:49:34 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 01:04:44 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 01:20:03 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 01:24:20 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 21 01:24:20 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:24:20 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:24:21 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:24:23 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:24:28 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:24:36 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 21 01:35:05 adsbexchange adsbexchange-feed[536]: BeastReduce TCP output: High latency, reducing data usage temporarily.
May 21 01:36:20 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 21 01:36:20 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:36:21 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:36:22 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:36:24 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:36:28 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:36:36 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005
May 21 01:45:22 adsbexchange adsbexchange-feed[536]: Beast TCP input: Remote server disconnected: 127.0.0.1 port 30005 (fd 7, SendQ 0, RecvQ 0)
May 21 01:45:22 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:45:22 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:45:23 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:45:25 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:45:30 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection to 127.0.0.1 port 30005 failed: 111 (Connection refused)
May 21 01:45:38 adsbexchange adsbexchange-feed[536]: Beast TCP input: Connection established: 127.0.0.1 port 30005

adsbexchange-mlat.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
May 20 22:53:46 adsbexchange adsbexchange-mlat[533]: Reconnecting in 10.1 seconds
May 20 22:53:57 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 20 22:53:57 adsbexchange adsbexchange-mlat[533]: Reconnecting in 11.0 seconds
May 20 22:54:08 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 20 22:54:08 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock
May 20 22:54:13 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection established
May 20 23:04:44 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection lost
May 20 23:04:44 adsbexchange adsbexchange-mlat[533]: Lost connection to 127.0.0.1:30005
May 20 23:04:44 adsbexchange adsbexchange-mlat[533]: Reconnecting in 2.0 seconds
May 20 23:04:46 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 20 23:04:46 adsbexchange adsbexchange-mlat[533]: Reconnecting in 11.9 seconds
May 20 23:04:58 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 20 23:04:58 adsbexchange adsbexchange-mlat[533]: Reconnecting in 10.3 seconds
May 20 23:05:09 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 20 23:05:09 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock
May 20 23:05:14 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection established
May 20 23:08:24 adsbexchange adsbexchange-mlat[533]: Receiver: connected     7.4 msg/s received        2.9 msg/s processed (39%)
May 20 23:08:24 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 20 23:08:24 adsbexchange adsbexchange-mlat[533]: Results:  1.0 positions/minute
May 20 23:08:24 adsbexchange adsbexchange-mlat[533]: Aircraft: 1 of 2 Mode S, 0 of 0 ADS-B used
May 20 23:08:26 adsbexchange adsbexchange-mlat[533]: peer_count:   0 outlier_percent: 0.2 bad_sync_timeout:   0
May 20 23:23:24 adsbexchange adsbexchange-mlat[533]: Receiver: connected     7.5 msg/s received        3.6 msg/s processed (47%)
May 20 23:23:24 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 20 23:23:24 adsbexchange adsbexchange-mlat[533]: Results:  0.5 positions/minute
May 20 23:23:24 adsbexchange adsbexchange-mlat[533]: Aircraft: 2 of 2 Mode S, 2 of 2 ADS-B used
May 20 23:23:28 adsbexchange adsbexchange-mlat[533]: peer_count:  29 outlier_percent: 0.4 bad_sync_timeout:   0
May 20 23:38:25 adsbexchange adsbexchange-mlat[533]: Receiver: connected     1.8 msg/s received        0.8 msg/s processed (44%)
May 20 23:38:25 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 20 23:38:25 adsbexchange adsbexchange-mlat[533]: Results:  0.0 positions/minute
May 20 23:38:25 adsbexchange adsbexchange-mlat[533]: Aircraft: 0 of 1 Mode S, 0 of 0 ADS-B used
May 20 23:38:31 adsbexchange adsbexchange-mlat[533]: peer_count:   0 outlier_percent: 0.0 bad_sync_timeout:   0
May 20 23:53:25 adsbexchange adsbexchange-mlat[533]: Receiver: connected     2.5 msg/s received        1.0 msg/s processed (40%)
May 20 23:53:25 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 20 23:53:25 adsbexchange adsbexchange-mlat[533]: Results:  0.2 positions/minute
May 20 23:53:25 adsbexchange adsbexchange-mlat[533]: Aircraft: 0 of 0 Mode S, 1 of 1 ADS-B used
May 20 23:53:35 adsbexchange adsbexchange-mlat[533]: peer_count:  23 outlier_percent: 0.3 bad_sync_timeout:   0
May 21 00:08:25 adsbexchange adsbexchange-mlat[533]: Receiver: connected     7.7 msg/s received        4.2 msg/s processed (54%)
May 21 00:08:25 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 00:08:25 adsbexchange adsbexchange-mlat[533]: Results:  0.0 positions/minute
May 21 00:08:25 adsbexchange adsbexchange-mlat[533]: Aircraft: 2 of 3 Mode S, 1 of 1 ADS-B used
May 21 00:08:40 adsbexchange adsbexchange-mlat[533]: peer_count:  31 outlier_percent: 0.4 bad_sync_timeout:   0
May 21 00:23:26 adsbexchange adsbexchange-mlat[533]: Receiver: connected     7.4 msg/s received        2.6 msg/s processed (35%)
May 21 00:23:26 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 00:23:26 adsbexchange adsbexchange-mlat[533]: Results:  0.0 positions/minute
May 21 00:23:26 adsbexchange adsbexchange-mlat[533]: Aircraft: 1 of 1 Mode S, 2 of 2 ADS-B used
May 21 00:23:29 adsbexchange adsbexchange-mlat[533]: peer_count:  21 outlier_percent: 0.0 bad_sync_timeout:   0
May 21 00:38:26 adsbexchange adsbexchange-mlat[533]: Receiver: connected     2.4 msg/s received        0.9 msg/s processed (37%)
May 21 00:38:26 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 00:38:26 adsbexchange adsbexchange-mlat[533]: Results:  0.0 positions/minute
May 21 00:38:26 adsbexchange adsbexchange-mlat[533]: Aircraft: 2 of 3 Mode S, 1 of 1 ADS-B used
May 21 00:38:33 adsbexchange adsbexchange-mlat[533]: peer_count:  37 outlier_percent: 0.1 bad_sync_timeout:   0
May 21 00:53:27 adsbexchange adsbexchange-mlat[533]: Receiver: connected     8.4 msg/s received        3.3 msg/s processed (40%)
May 21 00:53:27 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 00:53:27 adsbexchange adsbexchange-mlat[533]: Results:  4.7 positions/minute
May 21 00:53:27 adsbexchange adsbexchange-mlat[533]: Aircraft: 1 of 2 Mode S, 3 of 4 ADS-B used
May 21 00:53:34 adsbexchange adsbexchange-mlat[533]: peer_count:  37 outlier_percent: 0.2 bad_sync_timeout:   0
May 21 01:08:27 adsbexchange adsbexchange-mlat[533]: Receiver: connected    14.4 msg/s received        4.4 msg/s processed (30%)
May 21 01:08:27 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 01:08:27 adsbexchange adsbexchange-mlat[533]: Results:  1.7 positions/minute
May 21 01:08:27 adsbexchange adsbexchange-mlat[533]: Aircraft: 2 of 2 Mode S, 0 of 0 ADS-B used
May 21 01:08:35 adsbexchange adsbexchange-mlat[533]: peer_count:  28 outlier_percent: 0.1 bad_sync_timeout:   0
May 21 01:23:27 adsbexchange adsbexchange-mlat[533]: Receiver: connected     6.3 msg/s received        1.7 msg/s processed (27%)
May 21 01:23:27 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 01:23:27 adsbexchange adsbexchange-mlat[533]: Results:  0.7 positions/minute
May 21 01:23:27 adsbexchange adsbexchange-mlat[533]: Aircraft: 2 of 2 Mode S, 1 of 1 ADS-B used
May 21 01:23:36 adsbexchange adsbexchange-mlat[533]: peer_count:  30 outlier_percent: 0.5 bad_sync_timeout:   0
May 21 01:24:20 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection lost
May 21 01:24:20 adsbexchange adsbexchange-mlat[533]: Lost connection to 127.0.0.1:30005
May 21 01:24:20 adsbexchange adsbexchange-mlat[533]: Reconnecting in 3.7 seconds
May 21 01:24:24 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 21 01:24:24 adsbexchange adsbexchange-mlat[533]: Reconnecting in 10.8 seconds
May 21 01:24:35 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 21 01:24:35 adsbexchange adsbexchange-mlat[533]: Reconnecting in 11.5 seconds
May 21 01:24:47 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 21 01:24:47 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock
May 21 01:24:50 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection established
May 21 01:36:20 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection lost
May 21 01:36:20 adsbexchange adsbexchange-mlat[533]: Lost connection to 127.0.0.1:30005
May 21 01:36:20 adsbexchange adsbexchange-mlat[533]: Reconnecting in 3.0 seconds
May 21 01:36:23 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 21 01:36:23 adsbexchange adsbexchange-mlat[533]: Reconnecting in 11.3 seconds
May 21 01:36:35 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 21 01:36:35 adsbexchange adsbexchange-mlat[533]: Reconnecting in 11.9 seconds
May 21 01:36:47 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 21 01:36:47 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock
May 21 01:36:50 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection established
May 21 01:38:28 adsbexchange adsbexchange-mlat[533]: Receiver: connected     9.1 msg/s received        3.4 msg/s processed (37%)
May 21 01:38:28 adsbexchange adsbexchange-mlat[533]: Server:   ready         0.0 kB/s from server      0.0 kB/s to server
May 21 01:38:28 adsbexchange adsbexchange-mlat[533]: Results:  0.7 positions/minute
May 21 01:38:28 adsbexchange adsbexchange-mlat[533]: Aircraft: 0 of 0 Mode S, 3 of 3 ADS-B used
May 21 01:38:37 adsbexchange adsbexchange-mlat[533]: peer_count:  37 outlier_percent: 0.5 bad_sync_timeout:   0
May 21 01:45:22 adsbexchange adsbexchange-mlat[533]: Beast-format results connection with 127.0.0.1:30104: connection lost
May 21 01:45:22 adsbexchange adsbexchange-mlat[533]: Lost connection to 127.0.0.1:30005
May 21 01:45:22 adsbexchange adsbexchange-mlat[533]: Reconnecting in 3.2 seconds
May 21 01:45:25 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 21 01:45:25 adsbexchange adsbexchange-mlat[533]: Reconnecting in 11.0 seconds
May 21 01:45:37 adsbexchange adsbexchange-mlat[533]: Connection to 127.0.0.1:30005 lost: [Errno 111] Connection refused
May 21 01:45:37 adsbexchange adsbexchange-mlat[533]: Reconnecting in 10.2 seconds
May 21 01:45:47 adsbexchange adsbexchange-mlat[533]: Input connected to 127.0.0.1:30005
May 21 01:45:47 adsbexchange adsbexchange-mlat[533]: Input format changed to BEAST, 12MHz clock

adsbexchange-stats.service logs: 
-- Journal begins at Mon 2026-05-18 06:25:01 AEST, ends at Thu 2026-05-21 01:45:47 AEST. --
May 18 06:25:05 adsbexchange systemd[1]: Starting ADSBexchange Stats...
May 18 06:25:06 adsbexchange adsbexchange-stats[589]: Using existing valid UUID (xxxx-xxx-xxx-2f6e2b7429e1) from /boot/adsbx-uuid
May 18 06:25:06 adsbexchange systemd[1]: Started ADSBexchange Stats.
May 18 06:25:06 adsbexchange adsbexchange-stats[695]: Note: 'USE_OLD_PATH' is set.
May 18 06:25:07 adsbexchange adsbexchange-stats[695]: Using UUID [xxxx-xxx-xxx-2f6e2b7429e1] for stats uploads
May 18 06:25:07 adsbexchange adsbexchange-stats[695]: Using JSON directory [/run/readsb] for source data
May 18 06:25:07 adsbexchange adsbexchange-stats[695]: Using script's DNS cache (600 seconds)
May 18 06:25:20 adsbexchange adsbexchange-stats[695]: Failure resolving [adsbexchange.com], waiting and trying again...
May 18 06:25:30 adsbexchange adsbexchange-stats[695]: Failure resolving [adsbexchange.com], waiting and trying again...
May 18 06:25:30 adsbexchange adsbexchange-stats[695]: FATAL: unable to resolve adsbexchange.com even after 2 tries.  Giving up.
May 18 06:25:30 adsbexchange adsbexchange-stats[695]: DNS Error for adsbexchange.com, fallback ...
May 18 06:25:31 adsbexchange adsbexchange-stats[1580]: curl: (6) Could not resolve host: adsbexchange.com
May 18 06:25:31 adsbexchange adsbexchange-stats[695]: WARNING: curl process returned non-zero (6): []; Sleeping a little extra.
May 18 06:26:04 adsbexchange adsbexchange-stats[695]: Failure resolving [adsbexchange.com], waiting and trying again...
May 18 06:26:24 adsbexchange adsbexchange-stats[695]: Failure resolving [adsbexchange.com], waiting and trying again...
May 18 06:26:24 adsbexchange adsbexchange-stats[695]: FATAL: unable to resolve adsbexchange.com even after 2 tries.  Giving up.
May 18 06:26:24 adsbexchange adsbexchange-stats[695]: DNS Error for adsbexchange.com, fallback ...
May 19 21:45:42 adsbexchange adsbexchange-stats[2163]: curl: (28) Connection timed out after 10004 milliseconds
May 19 21:45:42 adsbexchange adsbexchange-stats[695]: WARNING: curl process returned non-zero (28): []; Sleeping a little extra.
May 19 21:46:05 adsbexchange adsbexchange-stats[2388]: curl: (28) Connection timed out after 10003 milliseconds
May 19 21:46:05 adsbexchange adsbexchange-stats[695]: WARNING: curl process returned non-zero (28): []; Sleeping a little extra.
May 19 21:46:14 adsbexchange adsbexchange-stats[2424]: curl: (7) Failed to connect to adsbexchange.com port 443: Network is unreachable
May 19 21:46:14 adsbexchange adsbexchange-stats[695]: WARNING: curl process returned non-zero (7): []; Sleeping a little extra.

/boot/adsbx-env 
# Default no serial single SDR mode
# use # to comment out for 1090 mode
RECEIVER_OPTIONS="--device-type rtlsdr --ppm 0"

# 1090 serialed SDR
# Remove # for 1090 serial mode
#RECEIVER_OPTIONS="--device 1090 --device-type rtlsdr --ppm 0"

DECODER_OPTIONS="--max-range 450"
NET_OPTIONS="--net --net-heartbeat 60 --net-ro-size 1200 --net-ro-interval 0.1 \
        --net-ri-port 30001 --net-ro-port 30002 --net-sbs-port 30003 \
        --net-bi-port 30004,30104 --net-bo-port 30005"
JSON_OPTIONS="--json-location-accuracy 2"

# uncomment (remove #) the following line to make the actual range outline persist reboots
#JSON_OPTIONS="--json-location-accuracy 2 --range-outline-hours 8760 --write-state-only-on-exit --write-state=/var/globe_history"

INPUT="127.0.0.1:30005"
RESULTS="--results beast,connect,localhost:30104 --results basestation,listen,31003 --results beast,listen,30157"
MLATSERVER="feed.adsbexchange.com:31090"
INPUT_TYPE="dump1090"
#INPUT_TYPE="dump1090 --privacy"
SERVERPORT="30005"

/boot/adsbx-978env 
RECEIVER_978_OPTIONS="--net-only"
DECODER_978_OPTIONS="--max-range 460"
NET_978_OPTIONS="--net --net-heartbeat 60 --net-ro-interval 0.5 --net-ro-port 0 --net-sbs-port 0 --net-bi-port 0 --net-bo-port 0 --net-connector localhost,30004,beast_out"
JSON_978_OPTIONS="--json-location-accuracy 2"

ENABLED=yes
#RECEIVER_OPTIONS="--sdr-gain 36.4 --sdr driver=rtlsdr,serial=978 --format CS8"
RECEIVER_OPTIONS="--sdr-gain 42.1 --sdr driver=rtlsdr --format CS8"
DECODER_OPTIONS=""
NET_OPTIONS="--raw-port 30978 --json-port 30979"

Log for last update 
WARNING: apt does not have a stable CLI interface. Use with caution in scripts.

Get:1 http://archive.raspberrypi.org/debian bullseye InRelease [39.0 kB]
Get:2 http://raspbian.raspberrypi.org/raspbian bullseye InRelease [15.0 kB]
Get:4 https://pkgs.tailscale.com/stable/raspbian bullseye InRelease
Get:5 http://download.zerotier.com/debian/bullseye bullseye InRelease [36.9 kB]
Hit:3 http://www.flightaware.com/adsb/piaware/files/packages bullseye InRelease
Get:6 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf Packages [13.2 MB]
Get:7 http://archive.raspberrypi.org/debian bullseye/main armhf Packages [330 kB]
Get:8 https://pkgs.tailscale.com/stable/raspbian bullseye/main armhf Packages [14.3 kB]
Get:9 http://raspbian.raspberrypi.org/raspbian bullseye/non-free armhf Packages [107 kB]
Fetched 13.8 MB in 7s (2,085 kB/s)
Reading package lists...
Building dependency tree...
Reading state information...
63 packages can be upgraded. Run 'apt list --upgradable' to see them.
2026-04-26 09:50:30 URL:https://raw.githubusercontent.com/ADSBexchange/adsbx-update/main/update-adsbx.sh [6522/6522] -> "-" [1]
Activating swap...
/usr/sbin/dphys-swapfile: ERROR: swap file /var/swap missing! you need to first run  /usr/sbin/dphys-swapfile setup  to generate one
Swap activated.

WARNING: apt does not have a stable CLI interface. Use with caution in scripts.

Reading package lists...
Building dependency tree...
Reading state information...
librtlsdr0 is already the newest version (0.6.0-3).
libusb-1.0-0 is already the newest version (2:1.0.24-3).
libzstd1 is already the newest version (1.4.8+dfsg-2.1+rpi1).
ncurses-bin is already the newest version (6.2+20201114-2+deb11u2).
zlib1g is already the newest version (1:1.2.11.dfsg-2+deb11u2).
The following packages were automatically installed and are no longer required:
  itcl3 libtcl8.6 raspinfo tcl tcl-tls tcl8.6 tcllib tclx8.4
Use 'apt autoremove' to remove them.
The following additional packages will be installed:
  cpp git-man liberror-perl libexpat1-dev libjs-jquery libjs-sphinxdoc
  libjs-underscore libpython3-dev libpython3.9 libpython3.9-dev
  libpython3.9-minimal libpython3.9-stdlib python3.9 python3.9-dev
  python3.9-minimal python3.9-venv
Suggested packages:
  cpp-doc gcc-multilib autoconf automake libtool flex bison gdb gcc-doc
  git-daemon-run | git-daemon-sysvinit git-doc git-el git-email git-gui gitk
  gitweb git-cvs git-mediawiki git-svn ncurses-doc make-doc python3.9-doc
  binfmt-support
Recommended packages:
  javascript-common libusb-1.0-doc
The following NEW packages will be installed:
  bc cpp gcc git git-man liberror-perl libexpat1-dev libjs-jquery
  libjs-sphinxdoc libjs-underscore libncurses-dev libpython3-dev
  libpython3.9-dev librtlsdr-dev libusb-1.0-0-dev libzstd-dev make python3-dev
  python3-venv python3.9-dev zlib1g-dev
The following packages will be upgraded:
  libpython3.9 libpython3.9-minimal libpython3.9-stdlib python3.9
  python3.9-minimal python3.9-venv
6 upgraded, 21 newly installed, 0 to remove and 57 not upgraded.
Need to get 18.1 MB of archives.
After this operation, 55.6 MB of additional disk space will be used.
Get:1 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf python3.9-venv armhf 3.9.2-1+rpi1+deb11u6 [5,412 B]
Get:2 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libpython3.9 armhf 3.9.2-1+rpi1+deb11u6 [1,414 kB]
Get:3 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf python3.9 armhf 3.9.2-1+rpi1+deb11u6 [468 kB]
Get:4 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libpython3.9-stdlib armhf 3.9.2-1+rpi1+deb11u6 [1,615 kB]
Get:5 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf python3.9-minimal armhf 3.9.2-1+rpi1+deb11u6 [1,629 kB]
Get:6 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libpython3.9-minimal armhf 3.9.2-1+rpi1+deb11u6 [796 kB]
Get:7 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf bc armhf 1.07.1-2+b1 [101 kB]
Get:11 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf git-man all 1:2.30.2-1+deb11u5 [1,831 kB]
Get:8 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf cpp armhf 4:10.2.1-1+rpi1 [19.9 kB]
Get:9 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf gcc armhf 4:10.2.1-1+rpi1 [5,196 B]
Get:10 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf liberror-perl all 0.17029-1 [31.0 kB]
Get:12 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf git armhf 1:2.30.2-1+deb11u5 [4,739 kB]
Get:13 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libexpat1-dev armhf 2.2.10-2+deb11u7 [122 kB]
Get:14 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libjs-jquery all 3.5.1+dfsg+~3.5.5-7 [315 kB]
Get:15 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libjs-underscore all 1.9.1~dfsg-3 [100 kB]
Get:16 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf libjs-sphinxdoc all 3.4.3-2 [127 kB]
Get:18 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libpython3.9-dev armhf 3.9.2-1+rpi1+deb11u6 [2,996 kB]
Get:17 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libncurses-dev armhf 6.2+20201114-2+deb11u2 [288 kB]
Get:19 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf libpython3-dev armhf 3.9.2-3 [21.7 kB]
Get:20 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf libusb-1.0-0-dev armhf 2:1.0.24-3 [70.8 kB]
Get:21 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf librtlsdr-dev armhf 0.6.0-3 [32.6 kB]
Get:22 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf libzstd-dev armhf 1.4.8+dfsg-2.1+rpi1 [317 kB]
Get:25 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf python3.9-dev armhf 3.9.2-1+rpi1+deb11u6 [501 kB]
Get:23 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf make armhf 4.3-4.1 [376 kB]
Get:27 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf python3-venv armhf 3.9.2-3 [1,188 B]
Get:24 http://raspbian.raspberrypi.org/raspbian bullseye/main armhf zlib1g-dev armhf 1:1.2.11.dfsg-2+deb11u2 [184 kB]
Get:26 http://mirrors.dotsrc.org/raspbian/raspbian bullseye/main armhf python3-dev armhf 3.9.2-3 [24.8 kB]
apt-listchanges: Reading changelogs...
Fetched 18.1 MB in 6s (3,099 kB/s)
(Reading database ... 
(Reading database ... 5%
(Reading database ... 10%
(Reading database ... 15%
(Reading database ... 20%
(Reading database ... 25%
(Reading database ... 30%
(Reading database ... 35%
(Reading database ... 40%
(Reading database ... 45%
(Reading database ... 50%
(Reading database ... 55%
(Reading database ... 60%
(Reading database ... 65%
(Reading database ... 70%
(Reading database ... 75%
(Reading database ... 80%
(Reading database ... 85%
(Reading database ... 90%
(Reading database ... 95%
(Reading database ... 100%
(Reading database ... 44224 files and directories currently installed.)
Preparing to unpack .../00-python3.9-venv_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking python3.9-venv (3.9.2-1+rpi1+deb11u6) over (3.9.2-1+rpi1+deb11u3+b5) ...
Preparing to unpack .../01-libpython3.9_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking libpython3.9:armhf (3.9.2-1+rpi1+deb11u6) over (3.9.2-1+rpi1+deb11u3+b5) ...
Preparing to unpack .../02-python3.9_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking python3.9 (3.9.2-1+rpi1+deb11u6) over (3.9.2-1+rpi1+deb11u3+b5) ...
Preparing to unpack .../03-libpython3.9-stdlib_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking libpython3.9-stdlib:armhf (3.9.2-1+rpi1+deb11u6) over (3.9.2-1+rpi1+deb11u3+b5) ...
Preparing to unpack .../04-python3.9-minimal_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking python3.9-minimal (3.9.2-1+rpi1+deb11u6) over (3.9.2-1+rpi1+deb11u3+b5) ...
Preparing to unpack .../05-libpython3.9-minimal_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking libpython3.9-minimal:armhf (3.9.2-1+rpi1+deb11u6) over (3.9.2-1+rpi1+deb11u3+b5) ...
Selecting previously unselected package bc.
Preparing to unpack .../06-bc_1.07.1-2+b1_armhf.deb ...
Unpacking bc (1.07.1-2+b1) ...
Selecting previously unselected package cpp.
Preparing to unpack .../07-cpp_4%3a10.2.1-1+rpi1_armhf.deb ...
Unpacking cpp (4:10.2.1-1+rpi1) ...
Selecting previously unselected package gcc.
Preparing to unpack .../08-gcc_4%3a10.2.1-1+rpi1_armhf.deb ...
Unpacking gcc (4:10.2.1-1+rpi1) ...
Selecting previously unselected package liberror-perl.
Preparing to unpack .../09-liberror-perl_0.17029-1_all.deb ...
Unpacking liberror-perl (0.17029-1) ...
Selecting previously unselected package git-man.
Preparing to unpack .../10-git-man_1%3a2.30.2-1+deb11u5_all.deb ...
Unpacking git-man (1:2.30.2-1+deb11u5) ...
Selecting previously unselected package git.
Preparing to unpack .../11-git_1%3a2.30.2-1+deb11u5_armhf.deb ...
Unpacking git (1:2.30.2-1+deb11u5) ...
Selecting previously unselected package libexpat1-dev:armhf.
Preparing to unpack .../12-libexpat1-dev_2.2.10-2+deb11u7_armhf.deb ...
Unpacking libexpat1-dev:armhf (2.2.10-2+deb11u7) ...
Selecting previously unselected package libjs-jquery.
Preparing to unpack .../13-libjs-jquery_3.5.1+dfsg+~3.5.5-7_all.deb ...
Unpacking libjs-jquery (3.5.1+dfsg+~3.5.5-7) ...
Selecting previously unselected package libjs-underscore.
Preparing to unpack .../14-libjs-underscore_1.9.1~dfsg-3_all.deb ...
Unpacking libjs-underscore (1.9.1~dfsg-3) ...
Selecting previously unselected package libjs-sphinxdoc.
Preparing to unpack .../15-libjs-sphinxdoc_3.4.3-2_all.deb ...
Unpacking libjs-sphinxdoc (3.4.3-2) ...
Selecting previously unselected package libncurses-dev:armhf.
Preparing to unpack .../16-libncurses-dev_6.2+20201114-2+deb11u2_armhf.deb ...
Unpacking libncurses-dev:armhf (6.2+20201114-2+deb11u2) ...
Selecting previously unselected package libpython3.9-dev:armhf.
Preparing to unpack .../17-libpython3.9-dev_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking libpython3.9-dev:armhf (3.9.2-1+rpi1+deb11u6) ...
Selecting previously unselected package libpython3-dev:armhf.
Preparing to unpack .../18-libpython3-dev_3.9.2-3_armhf.deb ...
Unpacking libpython3-dev:armhf (3.9.2-3) ...
Selecting previously unselected package libusb-1.0-0-dev:armhf.
Preparing to unpack .../19-libusb-1.0-0-dev_2%3a1.0.24-3_armhf.deb ...
Unpacking libusb-1.0-0-dev:armhf (2:1.0.24-3) ...
Selecting previously unselected package librtlsdr-dev:armhf.
Preparing to unpack .../20-librtlsdr-dev_0.6.0-3_armhf.deb ...
Unpacking librtlsdr-dev:armhf (0.6.0-3) ...
Selecting previously unselected package libzstd-dev:armhf.
Preparing to unpack .../21-libzstd-dev_1.4.8+dfsg-2.1+rpi1_armhf.deb ...
Unpacking libzstd-dev:armhf (1.4.8+dfsg-2.1+rpi1) ...
Selecting previously unselected package make.
Preparing to unpack .../22-make_4.3-4.1_armhf.deb ...
Unpacking make (4.3-4.1) ...
Selecting previously unselected package zlib1g-dev:armhf.
Preparing to unpack .../23-zlib1g-dev_1%3a1.2.11.dfsg-2+deb11u2_armhf.deb ...
Unpacking zlib1g-dev:armhf (1:1.2.11.dfsg-2+deb11u2) ...
Selecting previously unselected package python3.9-dev.
Preparing to unpack .../24-python3.9-dev_3.9.2-1+rpi1+deb11u6_armhf.deb ...
Unpacking python3.9-dev (3.9.2-1+rpi1+deb11u6) ...
Selecting previously unselected package python3-dev.
Preparing to unpack .../25-python3-dev_3.9.2-3_armhf.deb ...
Unpacking python3-dev (3.9.2-3) ...
Selecting previously unselected package python3-venv.
Preparing to unpack .../26-python3-venv_3.9.2-3_armhf.deb ...
Unpacking python3-venv (3.9.2-3) ...
Setting up libncurses-dev:armhf (6.2+20201114-2+deb11u2) ...
Setting up libzstd-dev:armhf (1.4.8+dfsg-2.1+rpi1) ...
Setting up libpython3.9-minimal:armhf (3.9.2-1+rpi1+deb11u6) ...
Setting up bc (1.07.1-2+b1) ...
Setting up libusb-1.0-0-dev:armhf (2:1.0.24-3) ...
Setting up liberror-perl (0.17029-1) ...
Setting up librtlsdr-dev:armhf (0.6.0-3) ...
Setting up libexpat1-dev:armhf (2.2.10-2+deb11u7) ...
Setting up make (4.3-4.1) ...
Setting up zlib1g-dev:armhf (1:1.2.11.dfsg-2+deb11u2) ...
Setting up cpp (4:10.2.1-1+rpi1) ...
Setting up git-man (1:2.30.2-1+deb11u5) ...
Setting up libjs-jquery (3.5.1+dfsg+~3.5.5-7) ...
Setting up python3.9-minimal (3.9.2-1+rpi1+deb11u6) ...
Setting up libpython3.9-stdlib:armhf (3.9.2-1+rpi1+deb11u6) ...
Setting up libjs-underscore (1.9.1~dfsg-3) ...
Setting up gcc (4:10.2.1-1+rpi1) ...
Setting up libpython3.9:armhf (3.9.2-1+rpi1+deb11u6) ...
Setting up git (1:2.30.2-1+deb11u5) ...
Setting up libjs-sphinxdoc (3.4.3-2) ...
Setting up python3.9 (3.9.2-1+rpi1+deb11u6) ...
Setting up libpython3.9-dev:armhf (3.9.2-1+rpi1+deb11u6) ...
Setting up python3.9-dev (3.9.2-1+rpi1+deb11u6) ...
Setting up python3.9-venv (3.9.2-1+rpi1+deb11u6) ...
Setting up libpython3-dev:armhf (3.9.2-3) ...
Setting up python3-venv (3.9.2-3) ...
Setting up python3-dev (3.9.2-3) ...
Processing triggers for mailcap (3.69) ...
Processing triggers for libc-bin (2.31-13+rpt2+rpi1+deb11u13) ...
Processing triggers for man-db (2.9.4-2) ...
Processing triggers for install-info (6.7.0.dfsg.2-6) ...
Failed to enable unit: Unit file gpsd.service does not exist.
[ERROR] Error in line 73 when executing: systemctl enable adsbexchange-first-run.service adsbx-zt-enable.service readsb.service adsbexchange-mlat.service adsbexchange-feed.service gpsd.service adsbexchange-gpsmon.service pingfail.service
2026-04-26 09:51:57 URL:https://raw.githubusercontent.com/dstreufert/adsbx-webconfig/master/update-webconfig.sh [851/851] -> "-" [1]

WARNING: apt does not have a stable CLI interface. Use with caution in scripts.

Reading package lists...
Building dependency tree...
Reading state information...
git is already the newest version (1:2.30.2-1+deb11u5).
The following packages were automatically installed and are no longer required:
  itcl3 libtcl8.6 raspinfo tcl tcl-tls tcl8.6 tcllib tclx8.4
Use 'apt autoremove' to remove them.
0 upgraded, 0 newly installed, 0 to remove and 57 not upgraded.
Cloning into '/tmp/update-webconfig'...

WARNING: apt does not have a stable CLI interface. Use with caution in scripts.

Reading package lists...
Building dependency tree...
Reading state information...
dnsmasq is already the newest version (2.85-1+deb11u1).
php is already the newest version (2:7.4+76).
php-cgi is already the newest version (2:7.4+76).
php-common is already the newest version (2:76).
php-fpm is already the newest version (2:7.4+76).
whois is already the newest version (5.5.10).
The following packages were automatically installed and are no longer required:
  itcl3 libtcl8.6 raspinfo tcl tcl-tls tcl8.6 tcllib tclx8.4
Use 'apt autoremove' to remove them.
0 upgraded, 0 newly installed, 0 to remove and 57 not upgraded.
already enabled
Cloning into '/adsbexchange/update'...
/adsbexchange/update /tmp/update-webconfig
'boot-configs/wpa_supplicant.conf' -> '/boot/wpa_supplicant.conf.bak'
/tmp/update-webconfig
Created symlink /etc/systemd/system/multi-user.target.wants/leds.service → /etc/systemd/system/leds.service.
Job for leds.service failed because the control process exited with error code.
See "systemctl status leds.service" and "journalctl -xe" for details.
--------------------------------------------
        update-webconfig complete.          
--------------------------------------------
rebooting...